Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Styles & brands we work with
- Whole-home duct cleaning
- Dryer vent cleaning
- Camera inspection
- Sanitizing & deodorizing
See the difference
Before
After
Before
After
Before
AfterHow Much Does Duct Repair & Sealing Cost in Frankford?
Duct repair and sealing in Frankford typically costs $350 to $1,200 for most homes, with $550 to $800 being the common middle for a full-house seal-and-repair job. Small single-run fixes like a disconnected joint or a torn flex collar often land near $250 to $450, while larger jobs with crushed trunk lines or multiple failed seams run $1,500 to $2,800. The written estimate you get on site sets the final price, and estimates here are free.
Frankford’s housing stock is the main reason those ranges move. Much of the neighborhood was built before 1960, and a lot of it still runs on original galvanized or early rigid duct with taped seams that have dried out over decades. Older systems leak at the joints, and some have sagged or disconnected runs in the basement or crawl space. When we scope a job in Frankford, we’re usually dealing with a mix of aged sheet metal and a few retrofit flex runs added over the years.
Duct Repair & Sealing Cost Breakdown (2026)
Here’s what the line items look like in the Frankford market. All figures are typical estimates, not quotes.
| Line Item | Typical Cost Range | What It Covers |
|---|---|---|
| Single joint or seam seal (spot repair) | $120 – $250 | Mastic or foil-tape seal at one failed joint or gap |
| Disconnected or collapsed run reconnection | $250 – $550 | Reattach or replace a single flex or sheet-metal run |
| Full-system duct sealing (mastic + tape) | $450 – $1,200 | Seal all accessible joints, seams, and boots on the whole system |
| Flex duct replacement (per run) | $200 – $450 | Replace torn, crushed, or kinked flex run with new insulated duct |
| Sheet-metal duct section rebuild | $400 – $900 | Fabricate and install replacement section in rigid duct |
| Duct cleaning before sealing | $300 – $600 | Full-system clean so sealant bonds to clean surfaces |
| Register boot seal and reseat | $40 – $90 each | Seal the gap between floor boot and subfloor or wall opening |
| Return-air chase sealing | $200 – $500 | Seal return chase gaps in walls and framing |
| Sanitizing after repair | $150 – $400 | Apply Guardsman-grade sanitizer to repaired system |
What pushes a Frankford job toward the top of a range is almost always the condition behind the walls and under the floor: rusted-through duct, duct that was taped with cloth-backed tape that has since failed and left a sticky residue to clean off, or a return chase that was never properly sealed when the house was built. Small jobs stay small when the leak is accessible and the duct is intact. They grow when a run has to be cut out and rebuilt, or when a low-ceiling basement means slower, more careful work.
Two costs are worth separating in your head. Sealing is cheaper than repair, because you’re closing gaps that already exist rather than cutting out and replacing material. And cleaning before sealing matters more than most people expect: mastic and foil tape don’t hold on a dusty, greasy duct surface, so the clean isn’t an upsell, it’s what makes the seal last.
What Affects Duct Repair & Sealing Pricing in Frankford
- Age and material of the ductwork. Pre-1960 galvanized duct in Frankford often has seams that have dried out and joints that no longer meet. Rigid sheet metal repairs differently than flex, and rusted sections can’t just be sealed over; they have to be cut out.
- Access. Duct in an unfinished basement is quick to reach. Duct buried behind finished drywall, in a tight crawl space, or above a plaster ceiling takes longer and costs more. Many Frankford homes have some finished basement space, which means at least some runs are boxed in.
- How many runs fail at once. One torn collar is a spot job. Five disconnected runs plus a leaking return chase is a system job. Sealing the whole system in one visit usually costs less per run than sealing one at a time over multiple visits.
- Whether the HVAC unit gets cleaned at the same time. If the air handler, blower, and coil are dirty, cleaning them alongside duct repair keeps debris from migrating back into freshly sealed duct. Bundling the HVAC clean with the duct work is often cheaper than two separate visits.
- Whether sanitizing is needed. If the system shows signs of moisture or microbial growth, a Guardsman-grade sanitizing application after repair adds to the bill. Frankford’s humid summers and damp basements make this more common than in drier markets.
- Dryer vent condition. Not part of duct sealing, but it’s the other venting hazard in the same house. Dryer vent cleaning is a separate service and worth folding into the same visit if the vent hasn’t been done.
How to Save on Duct Repair & Sealing
There’s no coupon that makes duct work cheap, and we don’t sell one. What actually lowers the number is doing the job once, correctly, with the right materials, so you’re not paying for the same joint twice.
- Get the estimate in writing before work starts. A written estimate with line items lets you see what’s repair, what’s sealing, and what’s cleaning. Estimates are free here.
- Fix the leaks before you upgrade the equipment. Sealing a leaky system first means any later equipment decision is made against a tight system, not a leaking one.
- Combine services in one visit. Duct cleaning, sealing, HVAC cleaning, and dryer vent cleaning in one visit usually costs less than four separate trips. They also let us clean before we seal, which is the order that matters.
- Ask about air quality add-ons after, not before. Honeywell and Aprilaire filtration and humidity solutions make sense once the system is sealed and clean. Adding them before the leaks are fixed just means filtered air leaking out through the same gaps.
- Don’t seal over a dirty system. A cheap seal on a dirty duct fails early. Paying once for a clean and a proper seal is the lower total.
Call (866) 690-7933 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Why Leaking Ducts Matter More Than the Price Tag
A leaking duct system does two things at once. It loses conditioned air before it reaches the room, so the system runs longer to hit the thermostat setting, and it pulls air from wherever the leaks are: basement, crawl space, garage, attic. In Frankford homes with older construction, that second effect is the one that matters, because the air being pulled in isn’t filtered or conditioned.
Sealing is the part of the job that fixes both problems. Repairing a crushed or disconnected run restores airflow to the room it was supposed to serve; sealing the rest of the system keeps the air where it belongs. We run this work with contractor-grade equipment rather than rental-store vacuums. Rotobrush rotary brush systems agitate and lift debris from duct walls. Nikro HVAC cleaning units provide suction and containment at the air handler. Abatement Technologies negative-air machines keep dust and contaminants under negative pressure during the work instead of letting them drift into living space, which is the same approach used in professional remediation.
That equipment matters most on a combined clean, repair, and seal job, where you’re disturbing years of buildup and then sealing the surface underneath. A surface-level pass won’t get the duct clean enough for sealant to bond. Our technicians have up to 10 years of experience with this kind of system work. For the broader picture of what a full duct cleaning covers before sealing, see air duct cleaning in Frankford.
Repair or Replace: Which Makes Sense in Frankford?
Repair is usually the right call when the duct is structurally sound and the leaks are at joints and seams. Replace when the duct itself is failing: rusted-through sheet metal, crushed flex that can’t be re-rounded, or runs that were sized wrong from the start. In Frankford’s older homes, the honest answer is often a mix. A house might have solid rigid trunk lines worth keeping and two or three flex runs added later that should be replaced outright.
The way to tell is to scope the system and look. Repairing and sealing a system that’s fundamentally sound typically runs $450 to $1,200. Replacing a large share of the duct runs pushes well past that, and on a system that old, replacement is sometimes the cheaper long-term decision. We’ll give you both numbers in the written estimate so you can compare them side by side. For the repair and sealing work specifically, see duct repair & sealing.
What a Duct Repair & Sealing Visit Involves
Understanding the sequence helps you compare estimates, because a low bid that skips a step is not actually cheaper.
- Scope and inspect. We trace the system, find the leaks, and check the condition of each run. This is where the estimate comes from.
- Clean. The system is cleaned with rotary brush and high-suction equipment so the surfaces being sealed are clean and dry.
- Contain. Negative-air equipment keeps dust from migrating into living space during the work.
- Repair. Disconnected, crushed, or torn runs are reconnected or replaced. Failed sections of rigid duct are rebuilt.
- Seal. Joints, seams, boots, and return chases are sealed with mastic and foil tape. This is the step that stops the leaks.
- Sanitize if needed. A Guardsman-grade sanitizer is applied where moisture or microbial growth was found.
- Test airflow. We confirm each register is moving air and that the repaired runs are delivering to the right rooms.
Safety matters here. Sheet-metal duct edges are sharp, and working around an air handler means working near electrical components and, in some homes, gas-fired equipment. Sealing a gas flue connector or a combustion air path incorrectly can create a real hazard. We flag that clearly: if your system has a gas furnace or water heater connected to the duct or flue, that connection needs a trained professional, not a homeowner with a roll of tape. We do not walk anyone through DIY repair on those components.
Why Frankford Duct Systems Leak the Way They Do
Frankford’s climate is the driver. Summers here are humid enough that duct running through an unconditioned basement sweats, and condensation on cold duct is what starts the rust on older galvanized work. Winters are cold enough that any leak in a supply run in an attic or crawl space wastes heated air before it reaches the room. Both seasons work against a system with dried-out seams.
The other local factor is the housing itself. A lot of Frankford’s rowhouses and older single-family homes were built with duct systems sized for the equipment of the time. When a newer, higher-capacity air handler gets installed on an old duct system, the extra static pressure finds every weak joint. That’s why a system that seemed fine for years suddenly starts whistling at the registers or leaving rooms cold. The leaks were always there; the new equipment just made them worse. Sealing brings the system back into balance with the equipment it’s actually running.
Does Duct Sealing Lower Energy Bills?
Sealing reduces the conditioned air lost before it reaches your rooms, and a system that loses less air runs less to hit the same thermostat setting. How much you save depends on how leaky the system was to begin with and how much of it we can access. A system with a few failed joints sees a modest difference. A system with a disconnected return chase and several open seams sees a larger one. We don’t quote a savings percentage, because the honest number depends on your house, and anyone who promises a fixed figure without scoping the system is guessing.
Do You Need Duct Sealing or Duct Cleaning?
They solve different problems, and most Frankford jobs need both. Cleaning removes the buildup inside the duct. Sealing closes the gaps that let unfiltered air in and conditioned air out. If your complaint is dust, odors, or allergy flare-ups, cleaning is the primary fix. If your complaint is rooms that never get comfortable or a system that runs long, sealing is the primary fix. When we scope a job, we tell you which one your system actually needs, and if it’s just one, that’s what we quote.
FAQs – Duct Repair & Sealing Cost
How much does duct repair and sealing cost in Frankford?
Most Frankford homes fall between $350 and $1,200, with $550 to $800 being the common range for a full-system seal and repair. Single spot repairs start around $120 to $250, and larger jobs with multiple failed runs or crushed trunk lines run $1,500 to $2,800. The written estimate sets the final price. Call (866) 690-7933 for a free estimate.
Is it cheaper to repair or replace ductwork?
Repair is cheaper when the duct is structurally sound: a full seal-and-repair typically runs $450 to $1,200, while replacing a large share of the runs costs more. Replacement makes sense when sheet metal is rusted through or flex runs are crushed beyond recovery. We quote both so you can compare them. Call (866) 690-7933 and we’ll scope your system first.
How much does duct cleaning cost before sealing in Frankford?
Duct cleaning typically runs $300 to $600 for a full system in Frankford. It’s a necessary step before sealing, because sealant won’t bond to a dusty or greasy duct surface. Cleaning and sealing in one visit usually costs less than booking them separately. Call (866) 690-7933 for a combined estimate.
Can you come today for a duct repair estimate?
Same-day estimates are often available, and estimates are always free. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Call (866) 690-7933 and we’ll find the next opening.
How long does duct sealing take and does it cost more for a bigger house?
A full-system seal and repair usually takes most of a day, and a larger home or a system with more runs costs more because there’s more duct to reach, clean, and seal. A single spot repair takes far less time and typically costs $120 to $250. Your written estimate will include the expected time and the per-line cost. Call (866) 690-7933 for a free quote.
Do you seal ductwork in commercial buildings too?
Yes. Duct repair and sealing covers both residential and commercial systems, and commercial work is scoped differently because of the larger duct runs and the need to coordinate around building use. Pricing follows the same per-job estimate model. Call (866) 690-7933 to schedule a walk-through.
Get a Free Duct Repair & Sealing Estimate in Frankford
If your system is losing air, whistling at the registers, or leaving rooms uncomfortable, the right first step is a scope and a written number. We bring contractor-grade equipment to the job: Rotobrush rotary brush systems, Nikro HVAC cleaning units, and Abatement Technologies negative-air containment, with Guardsman-grade sanitizing where needed and Honeywell and Aprilaire solutions available if the system needs an air quality upgrade after the seal. Ducts, HVAC components, and dryer vents all get handled in one service relationship, so you’re not coordinating three vendors.
Call (866) 690-7933 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. The local pro we connect you with is licensed and insured as their state requires, and the written estimate sets the final price.
Pricing reflects the Frankford market as of 2026. Air Duct Cleaning Frankford offers free estimates – call (866) 690-7933.
Written by the team at Air Duct Cleaning Frankford.
What Our Customers Say
"Quoted per system rather than the bait and switch per vent pricing everybody else in town uses. The number I was told on the phone was the number on the invoice."
- Ebony Mosley"My wife's allergies had been bad in this house since we moved in. It's been two months since they did the ducts and it's noticeably better. Not a miracle, but real."
- Shane Rhodes"Ran a negative air machine on the whole system rather than the shop vac on a stick that the cheap outfit down the road uses. Showed me the before and after photos from inside the trunk line and it was genuinely disgusting."
- Ryan Kowalski